Glossary

Rapid Prototyping

Rapid Prototyping – definition

Rapid prototyping is an engineering process used to create, test, and revise a robot subsystem or full mobile robot with short design iterations. In mobile robotics, the term covers both hardware and software. It includes quick fabrication of mechanical parts, temporary sensor mounts, early electrical integration, and incremental validation of control, perception, and autonomy software. The goal is not final product optimization. The goal is to reduce technical uncertainty early and to verify assumptions against real robot behavior.

In the UGV domain, rapid prototyping usually means building a testable configuration around a known base platform, then measuring whether it meets a defined requirement. Examples include validating LiDAR placement for SLAM, testing a new ROS 2 driver, checking wheel odometry quality, or verifying power budget under payload. On Leo Rover and Raptor Rover, rapid prototyping is typically performed by integrating sensors, compute modules, payload brackets, and ROS 2 nodes in stages, then testing on indoor or outdoor routes.

The concept is closely related to iterative development, hardware-in-the-loop testing, and proof-of-concept integration. It is not equivalent to ad hoc assembly. A valid prototype should still preserve traceability of interfaces, versions, and measured results.

Rapid prototyping in mobile robotics

A mobile robot prototype must combine mechanics, electronics, and software in one testable stack. This makes prototyping in robotics slower than in pure software, but still much faster than a full production-grade build if interfaces are standardized. ROS 2 helps because nodes, topics, parameters, launch files, and message definitions provide repeatable integration points.

For UGVs, a rapid prototype often includes these layers:

  • mechanical adaptation – sensor brackets, payload plates, enclosure changes, cable routing
  • electrical integration – regulated power, connectors, serial or Ethernet links, EMI checks
  • compute setup – onboard SBC or edge computer, containerized runtime, storage and thermal checks
  • ROS 2 integration – drivers, TF tree, calibration, logging, and navigation pipeline
  • field validation – traversability, vibration tolerance, localization drift, and runtime stability

On Leo Rover, rapid prototyping usually starts from the built-in Raspberry Pi compute unit and ROS 2 Humble or newer. This is suitable for driver bring-up, teleoperation, basic autonomy experiments, and low-to-medium compute perception tasks. For heavier payloads or more demanding compute, Raptor Rover is the more appropriate platform because it is designed for larger payload capacity and larger-scale field setups.

Why rapid prototyping matters on UGV platforms

UGV development has high integration risk. A sensor can be supported by ROS 2 but still fail in practice due to vibration, power drops, field of view occlusion, or poor TF calibration. Rapid prototyping reduces this risk by moving validation closer to the real platform.

Typical uncertainties that should be tested early include:

  • whether the sensor update rate is sufficient for the target speed
  • whether compute resources can sustain required node frequency
  • whether the robot frame tree is consistent with REP 103 and REP 105 conventions
  • whether the enclosure and mount maintain alignment after terrain excitation
  • whether the autonomy stack works with differential-drive kinematics

For example, a 2D LiDAR running at 10 Hz may be acceptable for low-speed indoor mapping on Leo Rover, but less suitable for rough outdoor motion where scan distortion and wheel slip increase. In such a case, the prototype must be evaluated with real odometry, IMU fusion, and terrain-induced vibration.

How rapid prototyping works in ROS 2

ROS 2 is commonly used as the integration layer for rapid prototypes because it separates device drivers, estimation, planning, and visualization into composable software blocks. A prototype can start from minimal teleoperation and then grow toward autonomous navigation.

A typical ROS 2 prototyping workflow on Leo Rover or Raptor Rover is:

  1. bring up base control and verify /cmd_vel, odometry, and TF
  2. add one sensor at a time and confirm message timing and frame alignment
  3. record data with rosbag2 for offline inspection
  4. integrate localization or SLAM
  5. run Nav2 or a custom autonomy stack in controlled tests

Common ROS 2 interfaces used during prototyping are listed below.

Function Typical ROS 2 interface Notes
Velocity command geometry_msgs/msg/Twist Usually published on /cmd_vel
Wheel odometry nav_msgs/msg/Odometry Used by localization and control
2D laser scan sensor_msgs/msg/LaserScan Typical input for SLAM and obstacle avoidance
IMU sensor_msgs/msg/Imu Requires frame and covariance validation
Camera image sensor_msgs/msg/Image Depth and stereo add compute load
TF transforms tf2_msgs/msg/TFMessage Must follow REP 105 frame conventions

Example launch structure for a prototype with LiDAR and Nav2:

prototype_stack:
  ros__parameters:
    use_sim_time: false
    robot_base_frame: base_link
    odom_topic: /wheel/odometry
    scan_topic: /scan
    map_frame: map
ros2 launch leo_bringup base.launch.py
ros2 launch lidar_driver lidar.launch.py
ros2 launch slam_toolbox online_async_launch.py
ros2 launch nav2_bringup navigation_launch.py

Key parameters and validation metrics

A rapid prototype is useful only if it is measured. In robotics, a prototype should be evaluated with numeric criteria tied to the intended use case. These metrics depend on the subsystem.

Useful validation metrics include:

  • sensor rate – for example LiDAR scan frequency in Hz, IMU update rate in Hz, camera frame rate in fps
  • end-to-end latency – command to motion, or sensor timestamp to processed output
  • localization drift – position error over distance or time
  • CPU, GPU, RAM, and storage usage during rosbag2 recording and autonomy runtime
  • power draw and thermal stability under peak compute load
  • map update rate and planning cycle time in Nav2

For ROS 2 software validation, command-line inspection is part of the prototyping process:

ros2 topic hz /scan
ros2 topic hz /camera/depth/image_rect_raw
ros2 topic echo /odom --once
ros2 run tf2_tools view_frames
ros2 bag record /scan /imu/data /odom /tf /cmd_vel

When the prototype targets autonomy, frame naming and orientation should remain consistent with REP 103 for units and coordinate conventions, and REP 105 for mobile platform frames such as base_link, odom, and map.

Use cases with Leo Rover and Raptor Rover

On Leo Rover, rapid prototyping is well suited to research and education tasks where the platform is modified often. Examples include adding a 2D LiDAR for SLAM, attaching a depth camera for obstacle detection, testing visual odometry, or validating a Docker-based ROS 2 deployment. Because Leo Rover is a four-wheel differential-drive mobile platform, prototyping should account for wheel slip, uneven terrain, and the fact that autonomous navigation is not provided out of the box. A navigation stack must be integrated explicitly.

On Raptor Rover, the same process applies but with larger payload and stronger emphasis on field deployment. Typical prototypes include multi-sensor masts, RTK GNSS integration, edge AI computers, or heavier inspection payloads. Raptor Rover is better suited when payload mass, mechanical volume, or power budget exceed what is practical on Leo Rover.

Limitations and trade-offs

Rapid prototyping reduces uncertainty, but it does not replace final engineering. Temporary mounts can introduce vibration. Prototype wiring can mask EMC issues. A ROS 2 stack that works in a lab may fail under outdoor lighting, dust, or unstable GNSS conditions. The engineer must decide which prototype findings are valid for production and which are artifacts of the temporary setup.

There is also a trade-off between speed and reproducibility. Fast changes are useful, but every prototype iteration should preserve versioned CAD, wiring notes, firmware revisions, ROS 2 package versions, and test logs.

Normative references and standards

In ROS-based mobile robotics, rapid prototyping should still align with established conventions and documented interfaces. Relevant references include ROS 2 documentation on nodes, launch, rosbag2, and TF; REP 103 for standard units and coordinate conventions; REP 105 for coordinate frames on mobile platforms; URDF conventions for robot description; and vendor specifications for sensors and compute hardware. Hardware claims such as range, frame rate, current draw, and operating temperature should always be checked against the manufacturer specification for the exact model used in the prototype.

See also